Now when it comes to partition door, we will first think of glass partition door, not only because it looks beautiful, but also because it is very practical, which can increase a sense of visual magnification of space, and it is also a choice with high cost performance.

玻璃移門由于其安裝方便，開啟靈活，節省空間等優點，現在很多家庭、辦公、娛樂場所都大量應用，成為必不可少的裝修材料。在我們選購客廳隔斷玻璃移門的時候會很迷茫，盡管如此在挑選時我們一定不能隨意的選購一個糊弄了之，所以炫威小編提醒您，在選購玻璃移門的時候，一定要先掌握一定的相關知識：

Glass sliding door is widely used in many families, offices and entertainment places because of its advantages of convenient installation, flexible opening and space saving. We will be confused when we choose the living room partition glass sliding door. However, we must not choose one to fool it at will, so Xuanwei Xiaobian reminds you that when we choose the glass sliding door, we must first master some relevant knowledge:

玻璃門廠家在安裝隔斷玻璃門是應注意：

The glass door manufacturer shall pay attention to the following when installing partition glass doors:

1、玻璃與基架不銹鋼框的結合不能太緊密，玻璃放入不銹鋼框后，在不銹鋼框的上部和側邊應留有3毫米左右的縫隙，該縫隙是為玻璃熱脹冷縮準備的。

1. The combination of glass and base frame stainless steel frame shall not be too close. After the glass is put into the stainless steel frame, a gap of about 3mm shall be left on the upper and side of the stainless steel frame, which is prepared for glass thermal expansion and cold contraction.

2、安裝玻璃隔斷門之前，要檢查玻璃的角是否方正，檢查不銹鋼框的尺寸是否正確，有否走形現象。在校正好的不銹鋼框內，定出玻璃安裝的位置線，并固定好玻璃板靠位線條。

2. Before installing the glass partition door, check whether the corner of the glass is square, whether the size of the stainless steel frame is correct and whether there is deformation. Set the position line of glass installation in the right stainless steel frame, and fix the position line of glass plate.

3、在安裝玻璃隔斷門時，用玻璃吸盤機把厚玻璃吸緊，然后手握吸盤把由2-3人將厚玻璃板抬起，移安裝位置。然后玻璃上部插入門框頂部的限位槽，把玻璃的下部放在底托上，玻璃下部對準中心線，兩側邊部正好封住門框處的金屬飾面對縫口，要求做到內外都看不見飾面接過口。

3. When installing the glass partition door, use the glass suction cup machine to suck the thick glass tightly, then hold the suction cup and lift the thick glass plate by 2-3 people to the installation position. Then insert the upper part of the glass into the limit slot at the top of the door frame, place the lower part of the glass on the bottom support, align the lower part of the glass with the center line, and the edges on both sides just seal the metal facing butt joint at the door frame. It is required that the facing joint can not be seen inside and outside.

4、再給玻璃隔斷門注口封膠時，要在頂部限位槽和底部底托槽口的兩側，以及厚玻璃與框柱的對縫處等各縫隙處，注入玻璃膠封口注膠時，由需要注膠的縫隙端頭開始，順縫隙均勻灌注，使玻璃膠在縫隙處形成一條表面均勻的直線，用塑料片刮去多余的玻璃膠，并用布擦凈膠跡。

4. When sealing the injection opening of glass partition door, glass glue shall be injected at both sides of the top limit slot and the bottom bottom support slot, as well as at the butt joint between thick glass and frame column. When sealing and injecting glue, it shall be poured evenly along the gap from the end of the gap where glue needs to be injected, so that the glass glue forms a uniform straight line on the surface at the gap, and the excess glass glue shall be scraped off with plastic sheet, And wipe the glue trace with a cloth.

5、玻璃之間對接，玻璃門固定部分因尺寸過大而需要拼接玻璃時，其對接縫要有2-3毫米的寬度，玻璃板邊要進行倒角處理。玻璃固定后，將玻璃膠注入對接的縫隙中。注滿后用塑料片在玻璃板對接縫的兩面將膠刮平，使縫隙形成一條潔凈的均勻直線，玻璃面上用干凈布擦凈膠跡。

5. When the fixed part of the glass door needs to splice glass due to its large size, the butt joint shall have a width of 2-3mm, and the edge of the glass plate shall be chamfered. After fixing the glass, inject the glass glue into the butt joint. After filling, scrape the glue on both sides of the butt joint of the glass plate with a plastic sheet to form a clean and uniform straight line, and wipe the glue trace on the glass surface with a clean cloth.