安裝濟南玻璃門時，先了解門的組件和門的類型，門的組件是門蓋，門頁，門鎖，鉸鏈和門觸，根據其功能分類，包括平開門，推拉門，折疊門，弧形門等。下面小編來講講具體的步驟吧！

When installing Jinan glass door, first understand the components of the door and the type of the door. The components of the door are the door cover, the door leaf, the door lock, the hinge and the door contact. According to their functional classification, they include the swing door, sliding door, folding door, arc door, etc. Now let's talk about the specific steps!

1.定位，放線：玻璃門結合固定玻璃和活動玻璃門扇，統一定位。

1. Positioning and setting out: the glass door shall be positioned uniformly by combining fixed glass and movable glass door leaf.

2.安裝框架頂部的限制槽：限制槽的寬度對于玻璃厚度應大于2-4mm，對于槽深度應大于10-20mm，安裝時，從繪制的線上拉出兩個金屬裝飾板邊緣，然后按側線，在門框頂部安裝限位槽。

2. Install the limit slot on the top of the frame: the width of the limit slot shall be greater than 2-4mm for the glass thickness, and the depth of the slot shall be greater than 10-20mm. During installation, first pull out two metal trim panel edges from the drawn line, and then install the limit slot on the top of the door frame according to the side line.

3.在木質底部安裝金屬飾面：將方木固定在地面上，然后用膠將金屬飾面粘在木頭上，方木可直接釘在預嵌木磚上，或通過膨脹螺栓固定。

3. Install metal facing at the bottom of the wood: first fix the square wood on the ground, and then stick the metal facing to the wood with glue. The square wood can be directly nailed to the pre embedded wood brick, or fixed by expansion bolts.

4.安裝垂直門框：將子彈的中心線連接到門框，然后用膠合板確定門框柱的形狀和位置，后外包金屬裝飾面。

4. Install the vertical door frame: connect the center line of the bullet to the door frame, and then use plywood to determine the shape and position of the door frame column, and then wrap the metal decorative surface.

5.安裝玻璃：用玻璃吸盤機吸入厚玻璃，然后握住吸盤將厚玻璃板抬起2-3人，移安裝位置。

5. Installation of glass: use a glass suction cup machine to suck in thick glass, then hold the suction cup to lift the thick glass plate by 2-3 people and move it to the installation position.

6.固定玻璃：木塊底部和側面有兩個小方形木條，厚玻璃夾在中間門上，方形木條距玻璃板表面約4mm，然后在方形木條上涂上通用膠將粘貼的金屬粘在方形條上。

6. Fixed glass: there are two small square wooden strips at the bottom and side of the wooden block, the thick glass is clamped on the middle door, and the square wooden strip is about 4mm from the surface of the glass plate, and then apply universal glue on the square wooden strip to stick the pasted metal on the square strip.

7.注塑玻璃密封：在頂部限位槽和底部支架的兩側，以及厚玻璃和框架柱等之間的間隙，進入玻璃密封。

7. Injection moulded glass seal: enter the glass seal at both sides of the top limit slot and the bottom bracket, as well as the gap between the thick glass and the frame column.

8.玻璃之間的對接：當玻璃門固定部分需要大尺寸拼接時，接縫寬度應為2-3mm，玻璃板邊緣應倒角。

8. Butt joint between glasses: When the fixed part of the glass door needs to be spliced in large size, the joint width should be 2-3mm, and the glass plate edge should be chamfered.

9.移動玻璃門安裝：在安裝門扇之前，應定位和安裝接地彈簧和門框頂面上的定位銷，兩者須是同軸的，安裝時，使用垂直線檢查以確保接地彈簧軸和定位銷的中心線在同一直線上。

9. Installation of movable glass door: before installing the door leaf, the grounding spring and the locating pin on the top surface of the door frame shall be positioned and installed. Both must be coaxial. During installation, the vertical line shall be used to check to ensure that the center line of the grounding spring shaft and the locating pin is on the same straight line.

10.安裝玻璃門扇上下門夾：在玻璃門的上下兩端安裝上下金屬門夾，測量門高。

10. Installation of upper and lower door clips of glass door leaf: install upper and lower metal door clips at upper and lower ends of glass door, and measure the door height.

要注意，在開始所有安裝步驟之前，須確保在施工完成之前基本完成室內裝飾和裝飾的其他過程，并且應嚴格定位對齊按照設計圖紙。更多相關內容就來我們網站http://www.traneyx.com.cn咨詢吧！

It should be noted that before starting all the installation steps, it is necessary to ensure that the interior decoration and other processes of decoration are basically completed before the completion of construction, and the alignment should be strictly in accordance with the design drawings. More relevant content will come to our website http://www.traneyx.com.cn Consult!